Blog

Fit the Mod Home with a Mod Fireplace

Modern  Fireplaces & Smooth Wall Finishes

 

In contemporary design, sleek rules.  Smooth surfaces, soft curves and industrial finishes abound.

 

In the fireplace world this usually means linear formats situated off the floor and elegantly breaking-up the wall enclosure.  The result is dramatic.

 

Getting to this look while protecting the surfaces from heat is an ongoing challenge.  Sheetrock is in itself susceptible to heat. Household paint finishes can rarely hold-up to high temperatures. Tape joints can crack from heat over time.  Fortunately, a combination of innovative wall products and fireplace design are successfully resolving some of these issues.

 

Let’s start with the wall/enclosure.  One way to beat the temperature issue around these fireplaces is the use of innovative wall products like Skamotec  Or Promafour board. These products provide a method for constructing the entire wall around the fireplace in a smooth and non-combustible enclosure.  This eliminates the risk of overheated walls or cracked tape joints. There is still the issue of finish coating on the wall and that requires research into the properties of the paint being selected for the project.  In many cases, only high-temperature industrial-type coatings will stand up to the heat generated around the opening of the fireplace. This may limit your color choices.

Expect temperatures around the opening to approach 200 degrees Fahrenheit or more.

 

Some fireplace manufacturers have developed wall designs that extract the heat around the fireplace and re-route it higher on the wall.  This allows the use of certain types of sheet rock and also permits the safe installation of electronics like TV screens above the fireplace.  Ortal fireplaces are a good example of this design.  More recently, Valor Fireplaces has developed their

Heatshift system to allow similar applications.  These systems provide much better temperature regulation for most household paints.

 

If you see a fireplace you like and the solutions above won’t work for you, then the best option is to design the fireplace to accommodate a stone, tile or other non-combustible finish around the fireplace opening.  In combination with a non-combustible backing board, this will eliminate the risk of having a wall crack or discolor.

 

 

 

October 01, 2018
Read More

Hot Air or Real Heat

The laws of physics tell us that if you move air over a hot surface you will increase the heat transfer efficiency from that surface.

Many stoves and fireplaces come equipped with fans specifically for that purpose.  Others provide air convection chambers so fans can be added as an option.  Still others have no capacity for fans.

For some the debate for and against fans on stoves and fireplaces is a point of contention with arguments favoring both sides.  Here is our take:

For products with integrated fan designs there’s evidence that efficiency is increased when the fan is in use.  This increase while it is real, may be hard to measure in terms of how it feels.

Stoves and fireplaces heat in two ways radiant & convective.  If a product is designed primarily as a radiant heater, then the presence of a fan often makes little difference in the amount of warmth you experience.  If the product is designed  as a convective heater, then the fan is apt to be more significant.

Keep in mind, most of our stoves and fireplaces are meant to work even when the power is out.  When this happens of course the fan will not function.  While there may be some drop in efficiency it is rarely significant and the stove or fireplace will continue to provide warmth.

Products designed for radiant heating will have very little if any benefit from the addition of a fan.  Where they have been tested, the efficiency difference is approximately 2% – 3%.

The electrical requirement for fans means additional installation cost if power is not already present in that location.  This is especially critical when inserts are installed in existing fireplaces.  Another issue is fan noise.  While fan technology has improved, there is going to be a certain amount of noise when they are in operation.  Controls enable us to lower their operating level and their output, but if the room is quiet you are likely to hear it.  Most of the fans utilized on fireplaces are capable of moving a maximum of 100 to 150 CFM.  This means you will certainly feel the warm air when you are within 2 or 3 feet of the fireplace.  However, this is typically not enough air movement to move heat from one room to another.  Natural air currents in the house will be responsible for that.  

If the fireplace you like and select has an integrated fan – don’t think twice.  It will be great and with or without power the fireplace will still heat.  If the fan is optional on the product you select then consider the expense of adding the fan relative to the benefit.  If it is a high-efficiency fireplace or insert then the fan is not likely to make a big difference.

 

November 28, 2017
Read More

Cooking with Gas

The time for outdoor living and barbecuing is upon us.  Not only are we seeing and smelling the blossoms of spring, but the smell and sizzle of the grill is starting to waft through our neighborhoods.

In his book Cooked,  Michael Pollan spells out the connection between our ability to cook food and our evolution as a species.  Of course the elemental form of this cooking is over a fire.  There is a reason we react to the smell of smoked and barbecued food – it  triggers an almost primal response that activates our taste buds and conjures images of good food, good friends and relaxing on the deck or patio under a warm sky.

After a rain-soaked winter our desire to be outside is only exceeded by our desire to fire-up the grill and enjoy our well-deserved time in the sun.  Both at home and here at Sutter Home & Hearth we are barbecuing and smoking everything from Roasts and Ribs to Russets and Radicchio.   If you’re yearning for something simple and delicious think about a roast chicken on the rotisserie or “drunk” chicken on your charcoal grill.  If you’re feeling more adventurous try Bobby Flay’s Paella  on your ceramic smoker.

Over the course of the Spring and Summer we will be grilling here at the store on Saturdays. We will feature Twin Eagles and Delta Heat gas grills, Green Egg and Kamado Joe ceramic smokers, Green Mountain pellet grills, Weber gas and charcoal grills (including the new Weber Summit Charcoal) as well as Solaire  infra-red  barbecues.  We’ll be hosting special events during the months of late May on through Mid July.  

While both men and women like to grill, I am always reminded of a British friend of ours who was amazed at the whole world of barbecue.  She deemed it the greatest invention by American Women.  “Not only does it get men to do the cooking,” she said,

“But it gets them to do it outside!”

 

CC1986_2

March 21, 2017
Read More

2 Hot for the Police & the Fireman

When is Hot Too Hot?

Radiant heat produced by wood and gas fireplaces warms any object in proximity to the heater.

Most of the time this heat is welcomed by us because it feels like the sun and warms us to the bone.  The byproduct of radiant heat is the gradual heating-up of walls and mantels close to the heat source.   In many cases after a fireplace has been on for awhile, nearby surfaces can be too hot to leave your hand on them or “too hot to the touch.”

Fortunately, the fact that they are too hot to touch does not mean that they are unsafe or likely to ignite.  Going back to the sun, have you ever walked on a wood deck drenched in the sun in your bare feet?  It’s like walking on hot coals.  Still, there is no record of a deck spontaneously igniting.

Once a surface gets much beyond our body temperature of 98.6 degrees F, it starts to feel hot to the touch.  Over the years, organizations like the National Fire Protection Association (NFPA),

Underwriters Laboratories (UL) and the National Bureau of Standards (NBS) have established standards for allowable temperatures on a variety of combustible materials.

Research tells us that for wood to ignite it must reach a minimum temperature of 482 degrees F.

There is evidence that if wood (and some other combustible surfaces like sheetrock) are exposed to sustained high temperatures over long periods of time their ignition temperature can be lowered.  It is at this point that codes & standards converge to tell us what is acceptable.

All this research and testing tells us that the critical temperature for potential danger is 187 degree F or approximately 117 degrees F above ambient room temperature.  It is to this temperature that heating appliances are tested.  When a fireplace is installed, the parameters for safe clearances are laid-out in the installation manual by the manufacturer.  The common denominator is that under extreme testing conditions, the nearby surfaces never reach the 187 degree temperature.

While walls and mantels remain safe at these temperatures sometimes the finishes (like paint or sealants) do not hold-up.  They can blister or peel in some cases.  This does not mean there is a safety concern, but it is a good idea to know what the temperature limitations are of the finishes applied to surfaces near fireplaces.

Too hot to the touch is a physical barrier we learn from childhood, but it is not necessarily a legitimate method of gauging the safety of a fireplace installation.

 

March 20, 2017
Read More

High-Tech & the Hearth

Technology seems to define and influence our behavior more than ever.  Of course this could just be

the whining of an ageing homo-sapien,  but  for as much promise as technology holds for us there is at least an equal amount of frustration as we adapt.  

When we consider our relation to fire it is not immediately obvious how much technology has

has influenced us.  We have moved from striking flint over dry straw to matches, butane lighters and firestarters.  The origins of camp fire building have evolved to The Top Down Burn.

EPA & Washington State certified stoves have evolved to limit our individual control of the stove or insert.  As long as we operate with dry wood and observe the basic tenants of  the owner’s manuals, it is almost impossible to create a smokey, inefficient fire.  EPA Label.  Yet, for those who believe they can learn nothing new,  fire building can harken back to our caveman roots and create unhealthy smoke and particulates.

Fortunately, fire technology has not stopped with wood burning.  Witness the evolution over the past several decades in gas burning and electric fireplaces.   While some would eschew the use of these sources of fire it is hard to argue that the beauty, style and efficiency of these products is very appealing.  Add to that the relative cost and ease of utilizing these products compared to wood and it is easy to understand their popularity.  Outdoor Great Room Wave or Amantii fire & Ice.

Once again the advancement of these products has not been restricted to their aesthetic qualities.

Over the past several years we have seen the development of  electronic ignition and remote controls that allow the fire to ignite without a traditional  standing pilot system.  These multi-function devices allow users to control flame height, heat output, fans and lights.  They also provide thermostat and timer functions in many cases.  Now we are on the cusp of having our fireplaces controlled by our smart phones (some of these are already in use).  

It’s true that time waits for no Man or Woman,  and like it or not our control of fire is blossoming with our technology.

 

March 20, 2017
Read More

Have you hugged your woodstove today?

Huggedyourstove copy

By way of introduction to the first “official” Sutter Blog, a little history seems in order.

I’ll try to keep it brief and edit out the juicy parts for later…

Starting a business in Seattle in 1979 was in many ways no different than starting one today.  There’s nothing like youthful exuberance mixed with naivete to propel us forward.

With a three-year background at a wood stove manufacturing company I was convinced that there were better products and a better way to bring them to the marketplace.

This was the genesis of the The Sutter Home Woodstove Co.  (catalog)

Cover_1

I found an old building vacancy on a Ballard Avenue that appeared  much different in 1979 than it does today.   On the cusp of the energy “crises”

VT02032016_0001

It made sense that high-efficiency cast-iron wood stoves could bring some energy independence to folks willing to cut, stack, store and age their heating fuel.  In 1980 I was joined by my future business partner John Miner.

I soon learned that many of our customers were unfamiliar with the nature of wood heat and discovered that our real job was to inform them of how these products could be safely installed and operated. (Wood & Energy by Jay Shelton).  The need for reliable information presented in an understandable fashion has shaped our philosophy ever since.

As more and more stoves came into use through the ‘80’s it was apparent that wood smoke and particulates from improper combustion were contributing to unhealthy air in our Emerald City.  As a result, woodstove manufacturers developed cleaner burning technology and we saw the evolution of gas-fired stoves and fireplaces.  Today, you can see the evidence of this technology in a broad selection of products with both fuel choices. (product shots?)

In the early days, the business was highly seasonal with stove sales and installations concentrated heavily in the months from September to March.  In 1982 we opened a 2nd location in Kirkland.  In 1986 we added barbecues to our product selection and moved our Kirkland store to Woodinville. 

VT02032016_0003

Most recently we move our Seattle store from Ballard Avenue to Leary Way in Ballard or as we like to call it; “Freelard” (between Ballard and Fremont) in September of 2011.  The following year (August of 2012) we were pushed out of our Woodinville location by the ever-expanding “Napa North” wine-tasting area.  Unable to find a suitable re-location and

influenced by the busy “season,” we elected to consolidate our business in the newer Leary Way location.

Sutter-Home-Hearth_03-12-14_027  

With our new larger facility we are able to display more product and with our talented installation, estimating and service crews we are still able to work from Vashon Island to

Bellevue and Mercer Island to Mukilteo. (pic of install truck).

A condensed history like this makes me feel a bit underwhelmed by what we have accomplished over the years.  However, from 2 people in 1979 we now number 25 and  believe that more growth is in our future.  I hope this wasn’t too boring for you.  My goal is to share more of our insights and experiences with you as this blog continues.

Blogart copy

February 13, 2017
Read More
  • Welcome to Sutter Home & Hearth

    Our site is designed to help you discover the warmth and beauty of fire. Not only will you see the range of products and services we offer, but you’ll have an opportunity to learn how these products can fit into your home. Our store in Seattle is full of operating stoves, fireplaces, inserts and barbecues. We are ready to assist you with practical knowledge as well as trained, certified installation and service.
  • Testimonials

    • We have looked other places at logs and we felt that they had the best prices and quality that we had seen.  The salesperson was helpful and informative.  The logs looked great in our living room.
      A. FalkA. Falk
    • They were very nice people to deal with.  They worked great and they were very prompt.
      D. KozieD. Kozie
    • We visited their showroom in Ballard and we decided to order our fireplace through them.  I was confused about their various options but they helped explain things quite well.  In the end, we got a great fireplace that didn't break the bank.  They also had to install it before the remodeling was completed, so they worked with the contractor to explain where the chimney had to go, etc.  After the remodel, they came over to teach us how to use the fireplace and help "break it in".  It really is the heart of the house thanks to them.
      F. ServitoF. Servito
    • We have a really small fireplace and were looking for a way to convert it to gas.  All other companies laughed at us given the size of the fireplace opening, but Sutter was really helpful and gave us some suggestions on where to find one that might fit.  We found one, they ordered it and installed it.  They also gave us great advice on a mason to help adjust some of the masonry work needed before the install.  Our new gas insert looks great, really warms up our living room in the winter and is a great focal point for the house.
      T.  SimpsonT. Simpson
    • Shawn, the office manger, was very helpful.  I went to every single place I could find and the price was comparable.  They have a more local store feel than the huge stores.
      C. BrownC. Brown